How do i Setup my Coredy Wi-Fi Extender?

Are you coping with the lagging network in streaming, chatting, and gaming, don’t concern too much. A superb option to reduce latency and network interference is the Coredy WiFi extender. It absolutely works with your prevailing network and maximises the Wi-Fi signals. This range extender completely boosts your network’s signal strength and also broadens the network coverage. Additionally, the WiFi dead zones are a thing of the past thanks to the Coredy range extender. The 2dBi external antennas are built-in on this extender that enhances the network coverage. In order to enhance or improve the Wi-Fi signals and coverage, the coredy wifi extender setup is vital.

How do I manually install a coredy Wi-Fi extender?

The Cordey WiFi Range Extender may also be managed using a web browser. Let’s follow the Coredy E300 setup guidelines provided below.

• You must first connect your operating systems, including those on your PCs and mobile devices, to the extender’s network.
• Your operating device can be ingeniously connected to the extender’s network from a Wireless N or Wireless AC network.
• Open a search engine right now, choose the address area, and type ap.setup or 192.168.10.1.
• The login wizard will then appear; enter your username and password to proceed.
• To boost the signal, you must choose a Wireless network name for your existing device.
• Now, just set up the Wi-Fi network for the dominant device in each section.
• Finally, click the Finish tab.

Note:- If you need any help regarding coredy wifi extender so contact our technician or visit the official page that ap extender setup.

WPS Setup for coredy wifi extender

Your WiFi extender’s WPS button setup on the WN300 is simple and practical. Let’s begin setting up the WPS buttons.

• You must first remove your Coredy WN300 WiFi Extender from the box and read the instructions for the device before using it.

• The Coredy Extender must now be connected to the wall outlet closest to the router.

• After that, you must locate and hold the extender’s power button. Wait until the extender’s power light is fully green before continuing.

• From now on, approach your Coredy WN300 extender, find, and press and hold the WPS button for a number of seconds.

• On your current wifi router, find and hold the Wi-Fi Protected Button as well.

• After that, you must wait until the LED light on the extender’s WPS turns steady green before looking at it.

• You can locate the WN300 extender at any other position while the WPS LED is continuously green.

Coredy Wi-Fi Extender Setup with 192.168.10.1

You can follow the procedures below to become certified to use the Coredy login interface and login. Let’s use the IP address to begin signing in to the WN300 extender.

• Connect your PC first to the Coredy extender’s network. Connect your PC easily using an Ethernet cable or Wireless N.
• The next step is to choose and use your favourite browser.
• You must type the IP address 192.168.10.1/ into the browser’s address bar and press Enter on your computer’s keyboard.
• You will occasionally notice the login page on your page.
• Enter the proper and valid username and password to log in.
• On the login ID and password tabs, enter admin.
• Finally, click the login button.

Coredy WN300 WiFi range extender setup as an access point

In most cases, the Coredy WN300 range extender offers multiple modes. The steps listed below should be followed if you want to set up the Coredy extender to function in access point mode.

• You must first log into your WN300 range extender before anything else.
• The extender’s home setup wizard will then appear.
• You may choose from a number of settings and mode options on the Home Setup Wizard.
• From among the several options, you must select access point modes.
• You must enter the SSID first on the access point interface.
• The Wi-Fi channel and security type must then be chosen.
• Finally, you must carefully fill out the password key.

Firmware update For coredy wifi extender

For the Coredy WiFi extender’s problem areas to be resolved, a firmware upgrade is required.

• Download the most latest firmware file before beginning the firmware upgrade.

• Then, go to your Coredy wifi extender’s admin setup.

• Choose and select the Upgrade Firmware tab next.

• You must load the most recent firmware file downloaded to the device to upgrade the firmware. Load the file by selecting the Browse tab.

• After the loading is complete, select the Upgrade tab.